#DUPONT멤브레인#RO멤브레인필터#TTPLUSHF#상업용멤브레인필터 DUPONT Product Data Sheet DuPontTM TapTecTM Residential Reverse Osmosis (RO) Elements TT Plus HF Element Description Product Type Typical Properties DuPontTM TapTecTM Residential Reverse Osmosis (RO) Elements provide a unique balance of reliability and value for performance through leveraging the proven technologies from DuPont - one of the most trusted solution providers in water treatment and the inventor of thin-film composite RO membrane, the core of modern RO technology. Focused on the local water conditions and water purifier operations, TapTecTM Plus HF RO Elements offer superior high flow performance with premium rejection and is flexible in 50GPD, 75GPD, 80GPD, and 90GPD water purifier system applications. Spiral-wound element with polyamide thin-film composite membrane TapTecTM Element TT Plus HF Element Dimensions Applied Pressure (psig) Permeate Flow Rate (bar) (GPD) 60 4.1 90 (ml/min) 236 Typical Stabilized Salt Rejection (%) 99 1. Permeate flow and salt rejection based on the following test conditions: 250 ppm NaCl, 77°F (25°C), pH 8.0, 15% recovery and the specified applied pressure. 2. Minimum salt rejection is 98.0%. 3. Minimum Flow Rate: 75GPD. A B NSF D COMPONENT This component is Tested and Centfed by NSF International against NSF/ANSI Standard 58 for materal requirements only. A B C D E DuPontTM ТартестTM Element (in.) (mm.) (in.) (mm) (in.) (mm) (in.) (mm) (in.) (mm) TT Plus HF 11.73 298 9.41 239 1.69 43 0.87 22 0.67 17 1. 20 TT Plus HF Residential Elements seal at a standard 2.0 inch -2.05 inch I.D. within pressure vessels Figure 1: Impact of Pressure on Target Permeate Flow (constant temperature, recovery) Figure 2: Impact of Temperature on Target Permeate Flow (constant pressure, recovery) 32 40 50 70 80 200 Pressure (psi) Operating and Cleaning Limits Maximum Operating Temperature a Maximum Operating Pressure Maximum Feed Flow Rate pH Range, Continuous Operation Maximum Feed Silt Density Index (SDI) 140 40 20 70 90 100 Temperature (F) Form No. 45-D02815-en, Rev. 4 113°F (45°C) 150 psig (10 bar) 2.0 gpm (7.6 1pm) 2-11 SDI 5 Additional Important Information Storage Product Stewardship Customer Notice Regulatory Note Free Chlorine Tolerance b b. <0.1 ppm Maximum temperature for continuous operation above pH 10 is 95°F (35°C). Under certain conditions, the presence of free chlorine and other oxidizing agents will cause premature membrane failure. Since oxidation damage is not covered under warranty, DuPont Water Solutions recommend removing residual free chlorine by pretreatment prior to membrane exposure. Please refer to FilmTecTM Design Guidelines for multiple-element systems of 8-inch elements (Form No. 45-D01695-en) for more information. Keep elements moist at all times after initial wetting. To ease installation, it is recommended to use a lubricant safe for indirect water contact on all seals. Potential options include water, glycerin based lubricants, and Molykote® 111 Compound. Rotate the element about a quarter turn to ease installation and removal of the element. Ensure good interface between the o-rings and brine seal with their connection surfaces. The use of this product does not necessarily guarantee the removal of cysts and pathogens from water. Effective cyst and pathogen reduction is dependent on the operation and maintenance of the system. DuPontTM TapTecTM Residential RO Elements may be covered under the TapTecTM Residential Element Limited Warranty, Form No.45-D00984-en. Contact a DuPont representative for more information. If operating limits and guidelines given in this Product Information Bulletin are not strictly followed, the Limited Warranty will be null and void. Refer to Storage and Shipping of New Film TecTM Elements (Form No. 45-D01633-en) for further information. DuPont has a fundamental concern for all who make, distribute, and use its products, and for the environment in which we live. This concern is the basis for our product stewardship philosophy by which we assess the safety, health, and environmental information on our products and then take appropriate steps to protect employee and public health and our environment. The success of our product stewardship program rests with each and every individual involved with DuPont products-from the initial concept and research, to manufacture, use, sale, disposal, and recycle of each product. DuPont strongly encourages its customers to review both their manufacturing processes and their applications of DuPont products from the standpoint of human health and environmental quality to ensure that DuPont products are not used in ways for which they are not intended or tested. DuPont personnel are available to answer your questions and to provide reasonable technical support. DuPont product literature, including safety data sheets, should be consulted prior to use of DuPont products. Current safety data sheets are available from DuPont. Please be aware of the following: The use of this product in and of itself does not necessarily guarantee the removal of cysts and pathogens from water. Effective cyst and pathogen reduction is dependent on the complete system design and on the operation and maintenance of the system. Permeate obtained from the first hour of operation should be discarded. This product may be subject to drinking water application restrictions in some countries; please check the application status before use and sale.