#DUPONT멤브레인#RO멤브레인필터#2540멤브레인필터#상업용멤브레인필터
DUPONT
Product Data Sheet
Description
FilmTecTM Membranes
FilmTecTM Seawater RO Elements for Commercial Systems
Improved FilmTec TM Seawater Reverse Osmosis Elements offer the highest productivity while maintaining excellent salt rejection.
• FilmTecTM SW30 Membrane Elements have the highest flow rates available to meet the water demands of both sea-based and land-based desalinators. FilmTecTM SW30 Elements may also be operated at lower pressure to reduce pump size, cost and operating expenses.
Improved FilmTecTM seawater membrane combined with automated, precision element fabrication result in the most consistent product performance available.
Typical Properties
Product SW30-2514
Applied Pressure
Permeate Flow Rate
Stabilized Salt
Part Number
psig (bar)
gpd (m3/d)
Rejection (percentage)
Minimum Salt Rejections (percentage)
80733
800 (55)
150 (0.6)
99.4
99.4
SW30-2521
80734
800 (55)
300 (1.1)
99.4
99.4
SW30-2540
12082989
800 (55)
700 (2.6)
99.7
99.5
SW30-4021
80740
800 (55)
800 (3.0)
99.4
99.2
SW30-4040
12082966
800 (55)
1,950 (7.4)
99.7
99.5
Element Dimensions
1. Permeate flow and salt rejection based on the following test conditions: 32,000 ppm NaCl, pressure specified above,25°C and the following recovery rates:
2.
SW30-2514-2percentage, SW30-2521, SW30-4021-5percentage, SW30-2540, SW30-4040-8percentage. Permeate flows for individual elements may vary +/-20percentage
3. For the purpose of improvement, specifications may be updated periodically.
Product
Small commercial
SW30-2514
SW30-2521
SW30-4021
Product
Large commercial SW30-2540
SW30-4040
C DIA
B-
D DIA
U-Cup Brine Seal
End Cap
Brinel
Feed
Fiberglass Outer Wrap
Product
Maximum Feed Flow Rate
gpm (m3/h)
6 (1.4)
6 (1.4)
16 (3.6)
Maximum Feed Flow Rate
gpm (m3/h) 6 (1.4)
16 (3.6)
FilmTec coupler part number 89055 is ordered separately for each element Each coupler includes two 2230 EPR Orings (part number 89255)
Dimensions - Inches (mm)
1 inch 25.4 mm
A
B
C
14.0 (356)
1.19 (30.2)
0.75 (19)
D 2.4 (61)
21.0 (533)
1.19 (30.2)
0.75 (19)
2.4 (61)
21.0 (533)
1.05 (26.7)
0.75 (19)
3.9 (99)
Dimensions - Inches (mm)
1 inch 25.4 mm
A
B
с
D
40.0 (1,016) 40.0 (1,016)
1.19 (30.2) 1.05 (26.7)
0.75 (19)
2.4 (61)
0.75 (19)
3.9 (99)
Operating and Cleaning Limits
1. Refer to FilmTecTM Design Guidelines for multiple-element systems of midsize elements (Form No. 45-D01588-en).
2. SW30-2514, SW30-2521 and SW30-2540 Elements fit nominal 2.5-inch I.D. pressure vessels. SW30-4021 and SW30-4040 Elements fit nominal 4-inch I.D. pressure vessel.
Membrane Type
Maximum Operating Temperature
Maximum Operating Pressure Maximum Pressure Drop
pH Range
Polyamide Thin-Film Composite
113°F (45°C)
1,000 psi (69 bar)
15 psig (1.0 bar)
Continuous Operationa
2-11
Short-Term Cleaningb
1-13
Maximum Feed Silt Density Index
SDI 5
Free Chlorine Tolerancec
<0.1 ppm
a.
Maximum temperature for continuous operation above pH 10 is 95°F (35°C).
b. Refer to FilmTecTM Cleaning Guidelines (Form No. 45-D01696-en).
C.
Under certain conditions, the presence of free chlorine and other oxidizing agents will cause premature membrane failure. Since oxidation damage is not covered under warranty DuPont Water Solutions
recommends removing residual free chlorine by pretreatment prior to membrane exposure. Please refer to Dechlorinating Feedwater (Form No. 45-D01569-en) for more information.
